Reliable vendors:
Most parts I have found cheapest and quickest delivery from Ebay.
| Vendor | Notes |
|---|---|
| backhoespareparts | |
| all_backhoe_parts | This is the same seller (Ray) with two stores/seller accounts. |
| Has parts manuals and can lookup parts by S/N. Very helpful and ships same day usually. | |
| greenglobeexports | In India. Has some harder to find parts. Shipping to US is 7-10 days. |
| They list parts with “make an offer” but rarely will take anything less than asking price. | |
| globalearthmovers | In India. Possibly same as greenglobe, but has tons of parts and shipped quickly. |
| Description | Service Interval | Capacity / Amount | JCB Part # | Parts Catalog Page | Cross Reference | Approx Cost (USD) | |
|---|---|---|---|---|---|---|---|
| Oil filter | Left front of engine. | 500 hours | 1 | 320/04133 320/B4420 | Napa 7233 | ||
| Wix 57233 | $40 | ||||||
| Oil | Fillers on top of engine front, and left side (both usable to fill) | 500 hours | 12-15L | CH-4/CJ-4 | |||
| 5w40 (-30c to 46c) 4001/2705 | |||||||
| 15w40 (-15c to 46c) 4001/1805 | Shell Rotella T6 Full Synthetic 5W-40 Diesel Engine Oil | $25 x 4 gallons | |||||
| Engine breather | Left side of engine, to right of oil filter | Housing 320/07735 | |||||
| First stage filter - , 320/07853 | |||||||
| Second stage filter - ? | p418 service manual | Donaldson P789407 | |||||
| Fuel Filter | Upper left under hood, on pump. | ||||||
| Filter wrench rec’d (loosen black collar only) | 500 hours | 1 | 320/A7123 filter only - superceded 32/925950 | ||||
| Bowl undermount is 32/925708 | L820-1-1 | $60 | |||||
| Fuel Filter / water separator | Underneath, lower left side of engine | 1000 hours | 1 | Entire assembly/mount - 333/Y6130 (includes filter/separator) | L810-10-1 | Donaldson P553550 | $32 |
| FEAT Accessory Belt | Front of engine | 500 hours | 1 | 320/08603 | $75 | ||
| Valve stem inserts | 4 | Type: TR CH3, Slime 20076 | $12 | ||||
| Hydraulic fluid | 2000 hours | 130L (34g) | AW46 ( | ||||
| AW32 ( | |||||||
| Hydraulic filter - return | Left side, under access plate on top of hydraulic reservoir | 100 hours | 1 | 32/925346 - normal service (12 micron) | |||
| 32/926001 - cleaning, 50hrs max (5 micron) | E540-5-1 | $80 cleaning | |||||
| $30 regular | |||||||
| Hydraulic filter gasket - return | See above | When access cover is removed, replace if old | 1 | 813/10186 | B130-5-1 | $15 | |
| Hydraulic filter - suction | Underneath, left side, behind oval plate on hydraulic reservoir’s right side | 2000 hours | 1 | 332/B1918 | $45 | ||
| Hydraulic filter gaskets - suction | See above | When access cover is removed, replacement recommended | 1 | ||||
| 40/302640 | $20 | ||||||
| Hydraulic filter - pilot (small) | Unknown / TBD | 100 hours | 1 | 32/925865 | E520-1-1 | $18 | |
| Transmission filter | Left side of transmission. Filter wrench rec’d. | 100 hours | 1 | 581/M8564 | $54 | ||
| Transmission fluid | Drain lower rear of transmission | 1000 hours | 11-16L (wet-dry, 4wd, syncshuttle) | 10w 400/2505 (-32c to 40c) | |||
| SAE30 4000/2605 (-5c to 46c) | Triax Transfluid Ultra TO-4, TRX7452 | $120 | |||||
| Transmission strainer | Lower rear of transmission | Clean 2000 hours | 1 | Gasket 813/50027 - replace each time strainer removed. | |||
| Strainer replacement 32/902200. | $20 for strainer. Gasket $2.50 @ dealer | ||||||
| Front axle fluid | |||||||
| Rear axle fluid | |||||||
| Front hubs fluid | 14mm hex to remove plug. Careful for air pressure release + spurt. | Not specified? | 2L per hub | 4000/0305 | Triax HD Gear Premium LS 80W-90, or any 80W-90 should be compatible | $36/gallon for Triax, $19 SuperTech brand | |
| Rear hubs fluid | 14mm hex to remove. | ||||||
| Careful for air pressure release + spurt. | Not specified? | 1.9L per hub | 4000/0305 | See above | See above | ||
| Crankcase ventilation filter | Not specific - very dirty and replaced | 320/07853 | Service manual 15-119 |
Most cab trim pieces are attached with flanged button head cap screw/bolts with a T30 torx. They hold water and are mostly all destroyed with rust, requiring to drill them out. Unclear how to easily replace the weld-on nut under the steel floor plate.
Replacing them with allen head now - tentatively M6 x 1.0mm thread x 25mm (JCB p/n is 826/01768)
For changing hub gear oil, raise entire machine via bucket + outriggers, then rotate wheels where oil drain is at top half.
Get a 5 gallon bucket and bungee straps, and place bucket as in picture:
Remove drain plug, then rotate tire so drain/fill hole will drain into bucket. When bucket is getting full, it can stretch the cord - so after the initial deluge of fluid I usually swap buckets or empty the bucket into another.
tbd